2 ISDN plants attach - VoIP General, VoIP News, VoIP Providers, VoIP hardware, VoIP software, VoIP Technology

Hello only times and congratulations on this marvelous and really informative forum

I have the following problem:

We are a small office community with 7 people. There we all are independent need everyone its own telephone. I have so far everything in such a way attached like it in my signature stand. This is in the long term however a very unsatisfactory solution, there max. 2 telephone calls (all the same whether fixed net or VoIP) across the T-sine 62 plant to be led can, since the S0-Bus gives no longer ago. We have still another second ISDN Basisstation (T-sine 300i) here rum, which I would attach gladly. Now the FBF has however only a S0-Eingang. With a distributor I do not come the distributor the needle eye, there then continue to be and no longer the T-sine 62. Is there a possibility the second basis station to attach and which additional hardware needs I then?

VG,

CS

Hello and cordially welcomely,

Starting point are thus ISDN terminals, across which you would like to hold more than two simultaneous conversations? That cannot be done with a Fritz box, since “only” the S0-Bus has and over a S0-Bus evenly only two discussions to go. There also no distributor helps.
You needed a second Fritz box with S0-Bus. Then you can hold simultaneous conversations up to 4 across the 2 basis stations.

Greeting

Marsupilami

a further 7050/5050 attach, and at the S0 the 2-Basis attach.

Or simply another equipment use, which is suitable for the employment with two internal S0, because over the Limitation of the two channels you do not come around. You can look at times the Lancom 1722…

Alternatively with the connection of two e.g. FBF 5012 in cascade (FBF 5012 number 1 at the ISDN office, number 2 at the HAIR DRYER S0 first) and connection of the two basis stations at HAIR DRYER S0 first in each case for the second plant as well as basis station 2 at the FBF number 2 HAIR DRYER S0 can additional be telephoned with four channels (VoIP) after outside. For ISDN logical-prove still only two channels are available.

--gandalf.

At best it you a correct TK-plant buys, for your case is in my opinion a FB together suitable.
With a TK-plant depending upon size one can attach mehere then connections, and one has also a better Progr.mglichkeit around the Anschl. to distribute etc. one has also more a/b interfaces.

I the variant suggested by muck1503 to prefer (7170 + 5012 or 5050), but not as of gandalf in cascade connection! Thus arriving ISDN calls would be blocked on the 2ten FBF also the S0 of the first FBF with 2!

Simply both FBF parallel to the NTBA and the Basen ever to a FBF.
Thus can one guarantees 4 conversations at the same time holding and with something luck and sufficient range also more, if further the connections HAIR DRYER 1-3 are along-used!

To the 5012 are then max. 2 discussions and
to the 7170 so ~3-4 discussions possible.

OK, OK ONE, only times best thanks so far for the answers

If I understood that correctly now, then I connect the second FBF (e.g. 5012) with the second exit of the NTBA (NTBA --> DSL/ISDN the FBF).

Over also for VoIP on the second FBF to use to be able I connect FBF 1 (LAN 2) with FBF 2 (WAN/LAN).

Can I those then also all 4 VoIP numbers on the two FBF's register, or do have I divide?

VG,
CS

You can register it into both,
but divide - according to the fixed net numbers - would be more meaningful.

Consider,
that you not from a FBF on the other one mediate/can connect!