Wrong announcement with Telefoniegerte 7270 - VoIP General, VoIP News, VoIP Providers, VoIP hardware, VoIP software, VoIP Technology

Hello together,

I did not find short looking for at least with anything over the following problem:

Since I deleted in the FB under “internettelefonie” two entries, the announcement of the assigned call numbers under “Telefoniegerten” does not tune no more at least in the overview. If I go editing on, the correct number is indicated. Unfortunately thereafter the announcement is still wrong in the overview.

I accomplished a RESET without result.
Any Tipps?

Quotation:

Quotation of Gringito

I accomplished a RESET without result.

what do you understand by it?
A.) PoR = 5 minutes everything Cable of the box removes
b.) Resetting over GUI/telephone code
C.) Recover

b)
Some Recover helps, seems logical, would however not like I for the moment not to accomplish. I wait up to the new firmware

Nevertheless it would interest me whether this problem arises only with me.

No, that is not only with you like that.
I attached the 7270 not until today and still am at the setting-up.

But the telephone attached with FON1 indicates another number in the overview with Telefoniegerte. It reacted nevertheless to the “correct” intended number and also with the Rausrufen is indicated correctly the number.

If I want to work on the attitudes for FON1, then e.g. become me Outgoing calls and also only to the following call numbers react several Internet call numbers doubles indicated.
If I select thereby the double, thus second same call number, then one can rausrufen with the telephone and not be involved it also no calls in.
In the overview then the correct number appears

I did not make a RESET yet.
Perhaps however nevertheless does somebody know, why wrong or also double numbers are indicated?
Under “Internettelefonie” the numbers stand only for 1x in it…

@Petraline, if you have 1+1 complete, then you should use first the starting code…

The starting code I entered!
Again: The call numbers under “Internettelefonie” everything correct-proves only 1x indicated.
With “Telefoniegerte” stand FON1, FON2 and DECT in it. Only with HAIR DRYER 1 the wrong call number is indicated. If I want to e.g. work on the call numbers for detailed calls with FON1, then there however the correct stands in it.
I times two pictures with attached, so that you see which I mean. In second one sees the folded up menu, if I open the call number selection. And some numbers stand exactly THERE twice in it.
If I select the upper *** 9020 for the FON1, then the correct NR is located in the main overview with “Telefoniegerte”, but one cannot telephone. Neither in detail nor outgoing.
If I select the lower *** 9020, then it folds perfectly, but the wrong NR is then located in the overview.

And NO, I entered none of the numbers manually, was already registered those all over the starting code.

At least I received that since already 2004

Hello Petraline,

that is a very strange behavior. Did you put the FB back already once to factory settings? If not, versuch' ask times, afterwards the starting code etc., if, then versuch' ask in .70er Recover. Here is one Guidance.

I can do me err, but sees to me sea-honour after “Konfigkuddelmuddel” out. Where do you get the box from, from 1&1? Hmmm, really, very strangely…

Actually I adjusted to it still nearly garnix. When I got the box months ago of 1und1 with the tariff change, I her to 1x attached, starting code entered, function examined and again removes. To today my 7050 used.

I times on factory settings will go tomorrow.
Does ' s give the possibility, e.g. the entered call barriers of exporting and then again of importing directory and the choice rules? Is otherwise much Tipperei…

You could make yourself a safety device of the configuration under system > Attitudes secure.

In order to rewind however again possible errors, and/or. to exclude that it was not because of the configuration, you should take better the starting code and again enter the remainder by hand. If you play a safety device back and there are really contained an error, then you fetch yourself back only again the “data salad” on the box.

You could make yourself Screenshots of the attitudes of the FB before, then it goes actually completely fixed.

Quotation:

Quotation of Petraline

Does ' s give the possibility, e.g. the entered call barriers of exporting and then again of importing directory and the choice rules?

That Fritz! Box monitor can - see appendix.
It can test before. FB Konfig secure and then full pipe rummachen.
The idea of Bibie functions also, but as one gets the monitor on the copier?

Quotation:

but how one gets the monitor on the copier?

Well completely simply: drauflegen and copy.

, To the FBM I did not think at all, with that laboratory, which I have for the moment drauf, he does not function so correctly.