FRITZ! Box of 7270 - two IP telephones + at the same time telefoniern - VoIP General, VoIP News, VoIP Providers, VoIP hardware, VoIP software, VoIP Technology

Hello municipality,

I htt there times again nen problem, with which I am dependent on your experience. I am of a dd WRT with SIP Proxy to Fritz! Box changed.

I possess two SIP of telephones and three accounts with sipgate. Property into the FB new L.G. drauf, then 3 the accounts with the appropriate numbers furnished. And too good lastly the two IP telephones in the box put on and everyone an own number for off and arriving calls fixed.

Folds marvelously, can telephone and call with both raus. Only problem which I straight discovered is that if on that one telephones to a telephone, then cannot I on that other no more be called (it goes equal the STARTING FROM of sipgate ran) and equivalent problem for outgoing discussions - it comes occupied.

Now is with the Linkys rout and Sipgate before gone… thus in principle possible. There the registration now the Fritz! Box makes (before were the SIP telephones) must it thus because of the box be.

Already a little geggoogelt, but really ne solution did not find.

That do not tap with the “call reject with occupied (Busy on busy)” deactivate funzt with the IP telephones, because there is not the option there. And as I already said each telephone its own account assigned got.

Heist now for me, I can telephone no longer at the same time?

Greeting,
Thomas

It forces to announce you nevertheless nobody the IP telephones at the internal SIP Registrar of the box…

Only because there is this internal Registrar, one does not have to use him still for a long time - you can register the IP telephones nevertheless also further directly with the Provider and the box only as if rout use…

The internal SIP Registrar of FBF 7170 and FBF 7270 with .70er L.G. has considerable restrictions… scan times the forum about SIP Registrar.

I would use the internal SIP Registrar only in emergency… e.g. if one wants with a IP telephone over a ISDN Festnetzanschluss of the box telefoniern.

hmm. without the “telephone system” in the box I did not want to do.
before all that gabs also with the SIP Proxy again and again (NAT) problems, why I am changed to the FBF…

there is really no solution for it… also not over telnet?

edit:
Meinste for instance the list:
http://www.ip-phone-forum.de/showpos...6&postcount=11

In the contribution linked by you I gathered only, which I found in the associated Thread and in other Threads… the result was considerable niederschmetternd for me.

But back to the box - you do not have to generally do without the features of the box. It does not concern (after my knowledge) one “either/or” decision (I hab' even still no S685IP… comes however shortly)
The S685IP can register on the one hand several call numbers (why thus not 1x or 2x directly with the Provider and 1x at the box)…
But even if that could not be done… over the similar haven you always come to the box and can use most features of the box over it, while the telephone is registered with the Provider parallel to it by SIP directly.

Sipgate is ideal as Provider in this connection, since Sipgate supports the multiple registration of numbers explicitly and permitted (I have e.g. my call numbers 3x registered - 1x in the FBF 7050 at the 1&1 DSL connection, 1x in the FBF 7170 behind the DIR-615 at the KD-connection, and once by X-pro Softphone hangs on a Notebook for on the way)

Well the attitudes for a SIP IP telephone behind one rout that also SIP call numbers registered is something tricky… You must evade on other WAN haven and these on LAN haven of the telephones (or the PC to rout) pass, you must for it firm IP addresses furnish, to etc. on….

The FBF can however… others rout (e.g. D-left) often call sowas “Virtual servers”. It is feasible… I have also in addition already Threads in the forum found… however it needs at the beginning of something reading in to one the connections understands and the terms correctly assigns.