separate selection MSN going off/arriving - VoIP General, VoIP News, VoIP Providers, VoIP hardware, VoIP software, VoIP Technology

Problem: FB 7170: L.G. .49

available: ISDN connection 3 MSN

NR 1 main call number
NR 2 fax
NR 3 “private”

at the similar MC MSN 1 for outgoing discussions is to be used, but not arriving called.
MSN 3 is to accumulate however arriving.
If I give MSN 1 in the attitudes as going off, this is arriving given automatically also for and cannot not be deactivated there. In the window for outgoing calls there is additionally 2 defaults, “fixed net” as well as an empty line with the call numbers. According to detailed hot wire discussion with its use a MSN is as desired used, so that it is thus possible that over MSN 3 or also FAX MSN going off one telephones depending on like the FB liked, thus a software problem, since so a configuration does not angedacht so far. Unfortunately I cannot test the variants at present extensively, since there active telephone enterprise prevails and is operationally used. If I select the MSN 3 arriving in the window for manual assignment, I am not safe whether then not possibly over this NR going off one telephones. This number is not however admits to become. Thus the CLIR and COLP would have to be activated, which should not have been.
An actually completely simple thing, which is probably not solvable however with the FB at present.
Did someone have perhaps similar problems and a solution did find?

Hello,

no. We had the question also frequently. Fact is: The MSN, which is going off used, is inevitably also an arriving MSN.

Not necessarily, see arriving and to releasing with going off the two fields with, only ' s becomes then evenly incalculable.

Quotation:

Quotation of rstle

........ at the similar MC MSN 1 for outgoing discussions is to be used, but not arriving called.
MSN 3 is to accumulate however arriving .......

With many ISDN telephones one can say, how often they are not to pass the bell clay/tone on, thus, how long they are to remain calm.
If you exchange thus MSN1 and MSN3, you would know your goal possibly. reach.

Is correct, but with Europe 11 one makes already head conditions around thing without spontaneous office getting to the FB to begin to be able. There I cannot afford still more “sprags”.

There were years ago (min 2007 or in former times) times firmware versions, there could one the outgoing number independently of the arriving number select. The first number was not there given with the arriving calls. Unfortunately that cannot be done momentarily any longer.

I find also shr unfortunate, because there are many scenarios, where one wants calls for a certain number at a certain connection directly empfanegn, but if one telephones raus, one wants to raustelefonieren with the main number.

With ISDN telephones or TK-plants one can make that and even if one selects a number manually with *1xx# before that to select. But unfortunately one cannot furnish this any longer firmly with similar and DECT connections.

Is for me not nachvollziebar, why AVM does not permit this possibility any longer, because software-technically is this reliably no large problem.

Hello rstle,

the outgoing MSN can you in any case with the choice rules furnish.
In each case, thus 0 to 9 a certain call number (gewnsche outgoing MSN) for the connection to the first selection digit assign.

Disadvantage: You do not have an allocation of the discussions on possibly. further MSN numbers.

Greetz

Fritzix

Around it the detailed thing and outgoing thing go are different. One cannot settle that with choice rules. Only if ALL calls are to go over an outgoing call number, then that can be done. Then one may have to run however no LCR.

FON1 starting from 11111 11111
FON2 starting from 11111 22222
FON3 starting from 33333 33333
DECT1 starting from 33333 44444

Lsst itself do not adjust 11111 always automatically also with FON2 and 33333 always with DECT1 one inserts there.

Quotation:

Quotation of jogruni

... there are many scenarios, where one wants calls for a certain number at a certain connection directly empfanegn, but if one telephones raus, one wants to raustelefonieren with the main number.

Naturally, that is an absolutely usual situation, which would apply also to my purpose. Is there any reasonable argument, why this is not possible (more)?

Graefe

HP: The trick with the choice rules would not function with me, because faxes with Sipgate always over a certain VoIP number must run.

Hello,
if you the Capi interface to be used the choice rules not used. In fax4box or also ffgtk you can specify the outgoing call number independently of the choice rules.

Greetz

Fritzix

Hello, as would be it with a Rufumleitung. With ISDN I do not know myself out, but with similar would have to go. Simply arriving discussions for the outgoing number of MSN 1 reroute immediately on MSN 3

Greeting

Alex

With Sipgate the possibility exists of specifying the indicated outgoing number. Allegedly this function is not to be supported however necessarily by the called connection. , I will times try Naja out.

I fear, the last possibility it then will be of hiding the outgoing MSN by CLIR.
Madly! AVM thanks!

Graefe