article.voiper.org

Custom Search
VoIPer Article>>>VoIP Providers>>Samsung SMT-G3010, SMT-G3210, SMT-G3220: rootfs patchen

Custom Search

Samsung SMT-G3010, SMT-G3210, SMT-G3220: rootfs patchen


2010-12-01
 
Nextiva is a cloud based VoIP phone system, hosting lots of small and medium sized businesses nationwide. the provides UNLIMITED business calling for only $19.95 a month!! Click here for the detail about this promotion!!

Guidance for providing an own update with changed root file system for Samsung rout.

A condition: Linux and the knowledge to deal with it.
  1. Official firmware (V2.03) take and unpack:
    tar xvf SMT….
  2. Submarine header of rootfs.img cut off:
    dd if=rootfs.img of=rootfs bs=64 skip=1
  3. unpack rootfs:
    sudo unsquashfs lzma rootfs
    thus the entire is put on rootfs under squashfs roots.
  4. Data change.
    For first I defined another root password and converted the start of telnetd.
    Files squashfs roots/etc./passwd and squashfs roots/etc./passwd change (new password Hash for roots)
    File squashfs root/etc/rc.d/rc.bringup_services_start:
    out if [- f /configs/etc/telnet_enable]
    becomes if [! - f /configs/ect/telnet_disable]
    Then telnet is default moderate on and can through put on the file /configs/etc/telnet_disable to be switched off.
    Further changes are now possible according to eigenm need.
    And now again everything pack up:
  5. Squashfs produce:
    sudo mksquashfs lzma squashfs roots rootfs - - noappend
  6. Submarine image generate:
    mkimage - T file system - n “Amazon rootfs “- C none - D rootfs rootfs.img
  7. Check total compute:
    sum rootfs.img
  8. File version info. status adapt:
    absolutely with ROOTFS_CHECKSUM register the correct check total
    as required: SYS_VER and DATE adapt (note: the format of SYS_VER is examined by the Web surface and must XX.YY reads (02.03p1 goes also, with the update is however not indicated. 2.03.1 it does not have routs accepted).
  9. Tar file pack:
    tar cvf SMTneu.tar *.img uImage version info. status
  10. And the result then rout as update offer. Subsequently, one has one routs with V2.03 and functioning Telenet entrance.

Programs:
mksquashfs lzma and unsquashfs lzma come from that here mentioned source. One takes the programs for squashfs version 2 and patcht the liking IC NUMBERs.
mkimage comes from Creative Commons denomination 3,0 DE Lizenz
I then times a installable Tarball for the SMT-G3210 made. I hab's with me tested, but use takes place on own responsibility.

http://bitflip.de/test/SMT-G3210_V2.03_090308mod.tar

Changes opposite the official 2,03 firmware:

- root password “banana”
- Telnet by default activates 30023 on haven
- newer dropbear SSH server inclusive. scp and dbclient
- starts dropbear with boats on haven 22, if the key file /configs/rsakey exists
- Ftp access to the whole system
- with boats it is gecheckt whether a file /configs/rc.local exists. If, it is implemented. (With it can start and terminate times programs thus automatically or implement instructions, if one liked.)
Hello!

I wrote a few Linux Skripte for the SMT-G3210. Whether to function I cannot say it also for the other models. Use on own danger!!!

The Skripte is for unpacking and providing the firmware tar file and for the .IAD configuration files. The IAD files function however only with the firmware v2.02

Samsung apparent changed the format of the.IAD file with firmware 2,03. Does someone have found out like it to unpack now leaves itself?

Everyone is to be verb-eaten cordially invited the Skripte and extended.

It the still following programs are needed: mksquashfs lzma, unsquashfs lzma and mkimage.
The sources in addition are linked in the Thread further above.
Quotation:
Quotation of chk2k2 Contribution indicate Samsung apparent changed the format of the.IAD file with firmware 2,03. Does someone have found out like it to unpack now leaves itself?
Here you are helped.
@SyncBit

Thank you….

Goes in the best way and me much work saved.

Actually only do I imagine myself that it hears the opposite side a quiet echo when telephoning of itself?
Young can't you the Squashfs of a Dbox use there? Linux is Linux. and there there is better Tools to administer and rewrite in an image.
Halli hello,

I wanted to change the root system:

SMT-G3010_V2.03_250208.tar

dd if=rootfs.img of=rootfs bs=64 skip=1

sudo/drunkenness/src/squashfs-3.0/unsquashfs-lzma firmware_mod_kit rootfs
Can't find to A SQUASHFS superblock on rootfs

sudo/drunkenness/src/squashfs-2.1-r2/unsquashfs-lzma firmware_mod_kit rootfs
Can't find to A SQUASHFS superblock on rootfs

unsquashfs lzma I have of
svn checkout svn: /svn.berlios.de/firmwaremodkit/trunk
download.

What now??

Did someone try, NFS or Samba on does rout to running to bring?


Thanks
Jiri
Hello,

Quotation:
Quotation of jiri.hladky Contribution indicate sudo/drunkenness/src/squashfs-3.0/unsquashfs-lzma firmware_mod_kit rootfs
Can't find to A SQUASHFS superblock on rootfs

sudo/drunkenness/src/squashfs-2.1-r2/unsquashfs-lzma firmware_mod_kit rootfs
Can't find to A SQUASHFS superblock on rootfs

unsquashfs lzma I have of
svn checkout svn: /svn.berlios.de/firmwaremodkit/trunk
download.

What now??
there you have the small, admittedly incomprehensible reference “one patchen for new A RISERs into the topic Samsung take the programs for squashfs version 2 and patcht the liking IC NUMBERs.” does not consider.

References, which could be meant with it finds you here.

To make too exciting but around it:

change in the file squashfs_fs.h SQUASHFS_MAGIC and SQUASHFS_MAGIC_SWAP into the liking IC NUMBERs used by Samsung:

// standard (original):
#define SQUASHFS_MAGIC 0x73717368
#define SQUASHFS_MAGIC_SWAP 0x68737173

// Samsung:
#define SQUASHFS_MAGIC 0x73716C7A
#define SQUASHFS_MAGIC_SWAP 0x7A6C7173

then it should function.
Well, it is really Hexerei. It functioned Thanks!!


Quotation:
Now I am with the u-boot-1.0.0 compiling.

After installing the
SOURCEs you configure submarine must for one specific board type. This
is done by typing:

make NAME_config

where “NAME_config” is the name OF one OF the existing
configurations;

What should I take?

By the way, it gives for the board a C-compiler (CROSS compiling)?

Thanks!
Jiri
Quotation:
Quotation of syncBit Contribution indicate [*] Submarine image generate:
mkimage - T file system - n “Amazon rootfs “- C none - D rootfs rootfs.img
Resounding oils,
up to then I also came now, but as the submarine package must be compiled, therefore question resembles as “jiri.hladky”…

Unfortunately is not deduced to me from the Doku, which Code:
make xxxx_config
I to implement should.

Gratefully for each reference!
Thus…

actually and attitudes necessary for that submarine of package would have to compile the information in from Samsung the ready racks SOURCE files to be found to have somewhere. So far however yet did not come to check there times. At the time of the Ursprungspostings there was not this Threads also yet at all.

It is not necessary also to comiplieren entirely the submarine of pacts since we want to build no Bootloader sonderen only the mkimage to need.

I rooted evenly times in history my shell, around to look which I at that time made. Looks like rather many unsuccessful attempts

But nevertheless times the following tries:

In the sublist tools submarine:

GCC crc32.c - I. /include - C
GCC mkimage.c crc32.o - I. /include - o mkimage

All data as usual without guarantee.

Much success
Quotation:
Quotation of syncBit Contribution indicate But nevertheless times the following tries:

In the sublist tools submarine:

GCC crc32.c - I. /include - C
GCC mkimage.c crc32.o - I. /include - o mkimage
Hello,
thanks for yours tap! Me was also clearly that one the whole package does not need, but mkimage on the idea, of through too hangeln am I not come

Anyhow if you modify your data geringfgug, then it fits:

Code:
1. CD…. /u-boat 1.0.0/lib_generic
 2. GCC crc32.c - I. /include - C
 3. CD…. /u-boat 1.0.0/tools
 4. GCC mkimage.c ../lib_generic/crc32.o - I. /include - o mkimage
... anyhow it folded in such a way with me!

Thanks!
After I had now some inquiries, have I unite small changes in my image described above made. The configuration files /etc/passwd, /etc/proftpd.conf and /etc/thttpd/thttpd.conf are now Symlinks after /configs/etc. Thus it becomes simpler, with these services rumzuspielen. With boats it is gecheckt whether these files under /configs/etc/ exist, and if not, becomes the standard configuration files there copied.


http://bitflip.de/test/SMT-G3210_V2.03_120508mod.tar

Hab's with me briefly tested, but is unofficial and unsupported, etc., blabla. And if your cat gets failure or the television has suddenly nen Gruenstich, do not give me the debt.
Hello,

but one cannot activate an alternative VoIP offerer thereby, or?
Because exactly that is nevertheless the primary problem with these sch…. SamsungBoxen!

Greeting

Sounddiver
Quotation:
Quotation of Sounddiver Contribution indicate but one cannot activate an alternative VoIP offerer thereby, or? Because exactly that is nevertheless the primary problem with these sch…. SamsungBoxen!
That is in the meantime the primary problem, after we solved the other problems.

But perhaps we should open in addition again their own Forschungsthread. There are at least starting points (one can activate a hidden menu option for other offerers), and I will not exclude that there still which goes. I have no alternative VOIP Provider, therefore my interest of research is not there large so. But perhaps we should gather again, which we have…
Yes, I find class…
Would you be so friendly and such Thread would open?
I handle me then gladly again also… (in the context of my limited possibilities)

Thanks

Sounddiver
hey
unfortunately I do not know myself so well with the whole software out
which I would make only gerene with mine samsung smt-g3010 (firmware V02.03), is a small program possess which rout with the Internet connects again thus that I a new IP had
goes sowas and if how?
would be grateful for an answer
mfg marqie
Quotation:
Quotation of xor16rox Contribution indicate Hab's with me briefly tested, but is unofficial and unsupported, etc., blabla. And if your cat gets failure or the television has suddenly nen Gruenstich, do not give me the debt.
that to update could be done without problems, fast and painless.
I come also at telnet on the haven 30023 ran, but the root password is not as expected banana.
$1$$CoERg7ynjYLsj2j4glJ34 says /etc/passwd to me. - thus admin…
also does not fold.
does someone have advice?
Quotation:
Quotation of v2px Contribution indicate I come also at telnet on the haven 30023 ran, but the root password is not as expected banana.
You see /etc/passwd over ftp? Can it be that with you the listing /configs/etc/ does not exist yet? IIRC gab's in the 1.XX firmware not yet, and I the checke existence of the listing at present not; I should probably do… Wenn's to it lies, should function it however with the image from Post2 in this Thread.

PM'e me times with more information, then we must here the Thread not zumuellen…
Quotation:
Quotation of Joergle Contribution indicate Hello,
thanks for yours tap! Me was also clearly that one the whole package does not need, but mkimage on the idea, of through too hangeln am I not come

Anyhow if you modify your data geringfgug, then it fits:

Code:
1. CD…. /u-boat 1.0.0/lib_generic
 2. GCC crc32.c - I. /include - C
 3. CD…. /u-boat 1.0.0/tools
 4. GCC mkimage.c ../lib_generic/crc32.o - I. /include - o mkimage
... anyhow it folded in such a way with me!

Thanks!

Hello,
I tried it, but without success:

Code:
GCC crc32.c - I. /include - C
 in file included from crc32.c: 12:
../include/common.h: 35: 20: error: config.h: NO look for file or directory
 in file included from ../include/common.h: 37,
                 from crc32.c: 12:
../include/linux/types.h: 14: error: expected `=', `,', `; ', `asm' or `__attribute__' before `dev_t'
 in file included from ../include/common.h: 80,
                 from crc32.c: 12:
../include/flash.h: 36: error: `CFG_MAX_FLASH_SECT' undeclared here (emergency in A function)
 ../include/common.h: 93: 64: error: asm/u-boot.h: NO look for file or directory
 ../include/common.h: 94: 74: error: asm/global_data.h: NO look for file or directory
 in file included from crc32.c: 12:
../include/common.h: 157: error: expected `)' before `*' tokens
 ../include/common.h: 308: error: expected declaration specifiers or `…' before `gd_t'
 ../include/common.h: 476: warning: conflicting type for built in function `PUTs'
 ../include/common.h: 477: warning: conflicting type for built in function `printf'
 ../include/common.h: 478: warning: conflicting type for built in function `vprintf'
 ../include/common.h: 494: warning: conflicting type for built in function `fprintf'
 ../include/common.h: 495: warning: conflicting type for built in function `fputs'
 ../include/common.h: 496: warning: conflicting type for built in function `fputc'


I tried then:
Code:
CD…./u-boot-1.0.0
 MAKEALL
 CD lib_generic/
GCC crc32.c - I. /include - C
It folded - however with many warnings:
Code:
In file included from ../include/common.h: 38,
                 from crc32.c: 12:
../include/linux/string.h: 15: warning: conflicting type for built in function `strspn'
 in file included from ../include/linux/string.h: 21,
                 from ../include/common.h: 38,
                 from crc32.c: 12:
../include/asm/string.h: 17: warning: conflicting type for built in function `strncasecmp'
 ../include/asm/string.h: 19: warning: conflicting type for built in function `strncpy'
 ../include/asm/string.h: 20: warning: conflicting type for built in function `' ../include/asm/string.h
 strlen: 23: warning: conflicting type for built in function `' ../include/asm/string.h
 memset: 24: warning: conflicting type for built in function `memcpy'
 ../include/asm/string.h: 25: warning: conflicting type for built into function `memmove'
 ../include/asm/string.h: 26: warning: conflicting type for built in function `memcmp'
 in file included from ../include/common.h: 38,
                 from crc32.c: 12:
../include/linux/string.h: 33: warning: conflicting type for built in function `' ../include/linux/string.h
 strncat: 39: warning: conflicting type for built in function `strncmp'
 in file included from crc32.c: 12:
../include/common.h: 476: warning: conflicting type for built in function `PUTs'
 ../include/common.h: 477: warning: conflicting type for built in function `printf'
 ../include/common.h: 478: warning: conflicting type for built in function `vprintf'
 ../include/common.h: 494: warning: conflicting type for built in function `fprintf'
 ../include/common.h: 495: warning: conflicting type for built in function `fputs'
 ../include/common.h: 496: warning: conflicting type for built in function `fputc'

Was it with you also like that?

Then already without problems:
Code:
CD ../tools/
 GCC mkimage.c ../lib_generic/crc32.o - I. /include - o mkimage
Is it so correct? Can I ignore the warnings?

Thanks!
Jiri
Quotation:
Quotation of jiri.hladky Contribution indicate Is it so correct? Can I ignore the warnings?
With me it goes in such a way without larger setting (from the u-boat-Toplevel-listing):

./mkconfig
./MAKEALL
(then comes ne quantity of error messages, which one can ignore, because we want only that the Makefile is provided for tools)

make

and then the programs in the tools directory without problem are compiled.
Quotation:
I come also at telnet on the haven 30023 ran, but the root password is not as expected banana.
I now still ne small change at a boat Script made, which should prevent such problems: We copy now with boats by default “banana” - passwd from /configs/etc/passwd.

Exception: if the file /configs/etc/newpass exists, we assume the user changed the passwd file consciously. Who changed thus the default password, simply this file should provide. On the box:

CD /configs/etc
touch new passport

http://bitflip.de/test/SMT-G3210_V2.03_220508mod.tar

Changes opposite the official 2,03 firmware.

(As always unofficial, unsupported and without guarantee…)
Are there changed 2,03 for the SMT-G3010 where the telnet entrance is de-energised possibly also?

Would be mad if that one make available could.

Merci already times!
Quotation:
Quotation of Alfistione Contribution indicate Are there changed 2,03 for the SMT-G3010 where the telnet entrance is de-energised possibly also?

Would be mad if that one make available could.

Merci already times!
And possibly. above mod. 2.03 also for the SMT-G3220?

Thanks and greeting

Sounddiver
Beautifully good day…
I have myself on mine rout (Smt-G3210) the frimware 2.03mod_220508 installed… function everything marvelously. However there are problems with the USB connection. All the same whether I attach a non removable disk or a USB stick, in the Web interface no connection is indicated.
Perhaps someone has an advice for me
Thanks
Can I, after I up-played mod.tar on my G3210 (completely normally over L.G. update, or?) also again back to original L.G.?

Thus does a very large risk exist that I shoot myself up the thing uselessly?

Did someone already try the experimental alternative Voip offerer out menu option? Experiences?

To thanks and here everything sounds quite geil
Now I it in such a way tried:

- Originals firmware 2,03 (for SMT-G3210) installs
- then *.iad the telnet installation additionally on rout installed
konfikurationsdatei believe I was from xor16rox (3210telnet, unpacked
she was called 3210-new.iad)

Now the USB stick becomes correctly erkannt*freu*. Also the telnet Client starts, but there is again an error here.
LOGIN IS INCORRECT
tried I…
Login: root
PW: banana
amzon
admin
mmhhh, which I make only wrongly????
Quotation:
Quotation of spear07 Contribution indicate mmhhh, which I make only wrongly????
Everything.

Forget these .iad - file, those was for an age-old version of the official firmware.

USB - DEVICEs are actually not gemountet automatically with my MOD at the moment, functioned however nevertheless. Simply on the box “usb mount” to enter should function. Or by hand for a standard USB stick:

mount - t vfat /dev/sda1 /mnt/usb-storage

One can also automate, by writing in the appropriate instruction into /configs/rc.local.

(Why that does not happen automatically at present, I do not know also exactly. Any Timing seems to be problem; I must regard on occasion again. The status data in the Web interface is by the way also not always correct. With above mentioned. Mount instruction is gemountet a USB stick, and also e.g. is. over ftp usably, but the status in the Web interface is nevertheless “emergency connected”)
if I the instruction:

mount - t vfat /dev/sda1 /mnt/usb-storage

, get I enter:

mount: Mounting /dev/sda1 on /mnt/usb-storage failed. NO look for DEVICEs or ADDRESS

Kinnas, times ne general note: this Thread actually addresses itself to people, which have a minimum of notion, and which v.a. also times to investigate can, if they discover a Problemchen. If it no pale glow have, which does it there, nevertheless times the question places to you whether you need really ne gepatchte firmware with telnet entrance on ne Linux box. , Remains with the official firmware and is lucky, or nervt freenet with the kindergarten questions does a favour to you. Those are paid to sound oneself. Nix for bad.
Here again a modified image with telnet and SSH for the new firmware design 3.00. Root password as had “banana”.

http://bitflip.de/test/SMT-G3210_V3.00_010608mod.tar

Changes opposite the official 3,00 firmware.

(As always unofficial, unsupported and without guarantee…)
Does this firmware support like orignal also strange voip offerer parallel to freenet?

Can be up-played thereafter also again the original L.G.?

Thank you
John BIeling
Quotation:
Quotation of jobisoft Contribution indicate Does this firmware support like orignal also strange voip offerer parallel to freenet?
Clearly.

Quotation:
Can be up-played thereafter also again the original L.G.?
Yes.
Ok one, the original inquiry stood here, but I think belonged in these thread. I installed the modified L.G. and changed also the file /ramdisk/etc/hosts, added the following line

192.168.78.1 more mysip.server mysip

However it always still does not function.

Which surprises me, in my internal lan nevertheless now ping more mysip.server too ping a 192.168.78.1 would have to be dissolved. It does not do however. Do I have “to reloaden” the host file somehow still, so that the changes are taken over?

Ping on more samsung.router functions and separates to the IP routers on…

Thanks
John
No, the problem must lie elsewhere, the “DNS error” in the log is not the true error message.

I with dyndns a new account anglegt (astelco.dyndns.org) on 192.168.78.1 zegt. That should repair exactly my problem, because the DNS dissolution completely normally functions (over Internet) and the IP then stop in my local LAN shows, nevertheless folds it not.

I remember it lie can that SIP Connections run only over the WAN interface and not over the LAN - confirm that someone?

Can one to it which turn?
Functions dyndns at all with local IP addresses?

You can pursue however in any case, which happens, because young from Samsung thank-worth-proves us nen pack Sniffer installed.
With the URL for the Web interface in /hidden/ - listing thus e.g. change: http://samsung.router/hidden/
Password is “free&net_samsung”. The noted packages one knows then with a program as we-rakes itself regards.

Looks in such a way, as if actually with registering a telephone number at of /etc/hosts - the file an DNS inquiry was past made for the Registrar entry.

All this has to do however so rather nix with modified Firmwares, and would be probably nevertheless in the Voip research Thread better waived.
hello
there it possible is the SMT-G3210_V3.00 to modify gives it intended also for the SMT-G3010-v3.00 a modified firmware with the telnet is activated or?
ask for imminent answer
mfg marqie
Thus SMT-G3210_V3.00_010608mod.tar in now brought, factory setting loaded and entrance data again entered.

If I tried micht with telnet to in-lure says it to me always Login incorrect:
Code:
telnet more samsung.router 30023
 roots
 banana
Which Mach I wrongly?
Quotation:
Quotation of Manfredxx Contribution indicate Which Mach I wrongly?
I assume times that you may not load factory settings, because otherwise the old password from /usr/default_db/default_db.tgz is restored. Thus before the shop of the work attitudes first times with telnet log in and the files /configs/etc/passwd and /configs/etc/passwd- in this archives change.

The Hash for “banana” is $1$$zZQKNjRd94GHyYOwXuStf0

Have A nice day
xorshadow
A simple restart should actually be enough. Probably the automatic restart interferes after the work RESET with the normal starting UP script.

A work RESET is not recommended however actually necessarily, because with it also all changes, which one made under /configs, inclusive. rsa key and adapted rc.local Skripte to be deleted. There one should store in any case before times the configuration.
Quotation:
Quotation of marqie Contribution indicate there it possible is the SMT-G3210_V3.00 to modify gives it intended also for the SMT-G3010-v3.00 a modified firmware with the telnet is activated or?
That is possible, and it is not heavy also at all, must itself stop only someone in addition aufraffen… I could provide already times on occasion an image, but I have neither time nor desire to maintainen. To that extent it would be better, if someone were, which also actually uses the crate.
Quotation:
Quotation of marqie Contribution indicate hello
there it possible is the SMT-G3210_V3.00 to modify gives it intended also for the SMT-G3010-v3.00 a modified firmware with the telnet is activated or?
Owing to the friendly support of xor16rox ' s gives it now also a version for SMT-3010: http://bitflip.de/test/SMT-G3010_V3.00_310508mod.tar

(do the already ne while, only owing to xor16rox give ' s give also to down-load now )

Changes to the official version as with the version for the 3210 (see: Changes)

and applies also here latrnich:
As always unofficial, unsupported and without guarantee…
Xorshadow, was to thanks really because of the work RESET.

Perhaps there is a possibility for reconnecten without the Internet telephone connection zutrennen, or few rauszufinden whether straight one telephones.
Quotation:
Quotation of Manfredxx Contribution indicate Perhaps there is a possibility for reconnecten without the Internet telephone connection zutrennen, or few rauszufinden whether straight one telephones.
Why at all reconnecten? One can deactivate that nevertheless under
Internet/Internet entrance/automatic reconnecting with the Internet?

Or does your Provider have a problem with a full-time circuit?

In this case you know the Reconnect in the same menu section into a communication-poor time (e.g. shift between 01:00 and 05:00).

Where thus is the problem?

Beautiful day wishes
Basis democrat
Quotation:
Quotation of xorshadow
Why at all reconnecten?
From time to time a new IP to have is sometimes completely useful.
Quotation:
Quotation of Manfredxx Contribution indicate From time to time a new IP to have is sometimes completely useful.
To be always attainable in addition. Straight one with Voip is a dial on and not necessarily the best solution. In addition it also the fastest creates routs hardly the connection on requirement delay-free to construct, which leads then both with the Surfen and when telephoning to disturbances.

My older trillion-rout had so a dial on and function. One could specify the connecting kinds, which retard the automatic dismantling of the connection and indicate a time of the Inaktivitt, after which the connection is diminished. With each renewed connection establishment again a new address was requested.

But unfortunately I had to state that

1. the address supplied by the Provider the same was frequent
2. the structure of the connection occasionally for a very long time lasted
3. releasing the ACPI PC-laterally for the loss of the IP address led (IP: 0.0.0.0), if rout straight were inactive. The PC had routs probably with its tiredness stuck on, so that this did not follow its DHCP obligations any longer in time.

Altogether the safety advantages of the dial on and did not convince me, because it has simply too many disadvantages.

Have A nice day
xorshadow
are there already modified 3,0 L.G. for Samsung a SMT-G3220?
Greeting, Stefanito
Hello together,

have also just the L.G. mod for 3210 Samsung installs everything sowiet in order, only I can not with telnet on rout access. What wrong do I make?

has to be implemented under telnet and be entered behind it the IP routers?
Quotation:
Quotation of twocores Contribution indicate has to be implemented under telnet and be entered behind it the IP routers?
Telnet is called as follows under Windows/start/implementing:

telnet more samsung.router 30023

Have A nice day
xorshadow
error message comes:

“telnet” could not be found.
Quotation:
Quotation of twocores Contribution indicate error message comes:

“telnet” could not be found.
In this case you must set a checkmark probably still under software/Windows Setup/connections with “hyperterminals”, because the program is along-installed automatically not with each Windows variant. To Windows XP hyperterminal is however at least a component of the operating system, which can be selected in the software Setup.

Starting from Windows Vista must be downloaded hyperterminals as supplementary product line, because the normal Vista user with such banalities may not be troubled such as telnet any longer. Probably next HTTP is painted, because is also too complicated.



Have A nice day
xorshadow
@ xorshadow

, so evenly hyperterminal thanks client in the Vista activated and it functioned. Be that with in-lied password can one does not see???
Quotation:
Quotation of twocores Contribution indicate Be that with in-lied password can one does not see???
That is like that standard because of security. In principle one in addition, stars could to the Client have sent, without gefrden security all too much.



Have A nice day
xorshadow
ok, all clear. Is it actually meaningfully after that bottles mod of the firmware factory settings zuladen, or hands only restart routers?
Quotation:
Quotation of twocores Contribution indicate ok, all clear. Is it actually meaningfully after that bottles mod of the firmware factory settings zuladen, or hands only restart routers?
Restart is enough, since at least with a 3.00-Mod-Version by putting back to factory settings the new root password with the unknown password of the original version is overwritten.

Have A nice day
xorshadow
can you to me still say which the number of 30023 for a meaning have?

Quotation:
telnet more samsung.router 30023

Quotation:
Quotation of twocores Contribution indicate can you to me still say which the number of 30023 for a meaning have?
The normal telnet works on haven 23, the Samsung-SMT-G3xxx-Telnet against it on haven 30023. Since this deviates from the standard, one must communicate it to the telnet program when starting.

Have A nice day
xorshadow
Quotation:
Quotation of xorshadow Contribution indicate The normal telnet works on haven 23, the Samsung-SMT-G3xxx-Telnet against it on haven 30023. Since this deviates from the standard, one must communicate it to the telnet program when starting.

Have A nice day
xorshadow
then I again which in addition learned
routs Mach of the v3 had mod firmware on factory settings nevertheless zurcsetzten, because rout yourself constantly on hung. Password remained however with banana, thought becomes other password???
Quotation:
Quotation of twocores Contribution indicate routs Mach of the v3 had mod firmware on factory settings nevertheless zurcsetzten, because rout yourself constantly on hung. Password remained however with banana, thought becomes other password???
With the newest update for the G3010 the colleague did not in-maintain that already, with the older Mods for the other models functioned that yet.

Beautiful day wishes
xorshadow
Moin @all,
have a giant to freenet completely changed and Samsung 3010 Phone SL received. DSL went immediately and without problems, however I had not noticed that I do not call with my similar telephone against-get. To telephone does not go being called.
Me about your assistance much would make happy.

mfg bexx
Quotation:
Quotation of bexx Contribution indicate To telephone does not go being called.
Your question is here in the Forschungsthread to modified firmware designs rather wrongly at the place. I hope much that the operator furnishes finally a Sammelthread of “configuration problems” sometime for each Provider. Momentarily postet here everyone simply wildly drauf loosely and furnishes a new Thread for configuration problems either or writes connectionless in one the existing. Thus the forum becomes quite unclear.

To your question: Probably either the entrance data are not correctly entered (the entrance data for the main call number and the Nebenrufnummern are differently entered with freenet-completely Voip!) or you did not configure correctly the PBX in the box. The analog telephone is not in any case the cause for the fact that you do not get calls.

Freenet has a completely reasonable on-line assistance for such problems:

http://www.freenet.de/hilfe/iphone/h...010/index.html

Above all the following three left could be helpful for your problem:

http://www.freenet.de/hilfe/iphone/h...ent/index.html
http://www.freenet.de/hilfe/iphone/h...lle/index.html
http://www.freenet.de/hilfe/iphone/h...len/index.html

If it should not function after careful control of all inputs yet, then that is a case for the freenet support.

Have A nice day
xorshadow
It would be conceivable, mod. Firmware for the G3210 around serves rcapi too erwetern? So that without a ISDN cable over rcapi client on my LinuxKiste Capi functioned?

Thanks for your troubles
I mean that will not go, since the Telefonie program is a closed Binary. But instructs me gladly a better!
Greeting
mhdot
Even if it was already asked here a few marks:
Is there already a finished image for the G3220?

Greeting
WebZ@k
Quotation:
Quotation of xor16rox Contribution indicate SSH for the new firmware design 3.00. Root password as had “banana”.
(As always unofficial, unsupported and without guarantee…)
Have you already the changes for those SMT-G3210_V3.01_210708.tar converted?
Quotation:
You already the changes for SMT-G3210_V3.01_210708.tar converted?
Oh, had not received at all that there is ne new firmware design.

http://bitflip.de/samsung/SMT-G3210_V3.01_130808mod.tar

That runs with me since today without problems. Like always without support and without guarantee. Changes opposite the official firmware as had.

I now times ne small Website cobbled together, in order resources scattered over the forum for Samsung rout a little to bundle. If still ne meaningful addition, always ago thereby breaks in to someone.

http://bitflip.de/samsung/
Quotation:
Quotation of WebZak Contribution indicate Even if it was already asked here a few marks:
Is there already a finished image for the G3220?
The problem with the G3220 is stop that I cannot test for lack of hardware. Therefore it would be good, if as with the G3010 someone were, which possesses actually sone crate. With the instructions, which gepostet syncBit, that is really not more difficult…

Because I was degree thereby, I now however times rehearse for the sake of an image for the G3220 made. That means however by no means that I will make for it further updates. On the contrary, I have for it actually no time and desire. Thus Freiwillige forwards.

Warning: the thing is absolutely untested. The probability that which goes inclined do not consider I very largely, but at least theoretically knows ne box scrap irons. Use RK your own risk.

http://bitflip.de/samsung/SMT-G3220_V3.00_140808mod.tar

And if someone dares, which to bottles, please as soon as possible it acknowledges whether the box still lives. In emergency one could probably at the serial console still which save, see. here and here.
Hello
I have the 3220 for me the image this evening or at the latest at the incoming goods times on the box will make. As I see could I thereby finally also times my USB HDD with ext3 mounten
Help to test gladly with.

MfG
Happy
Hello,

the image for the G3220 on my nigelnagelneuen has routs tried out. That rout bootet. I had not before otherwise tried it out unfortunately. It does not synchronize simply at my connection.
If I down degrees to the 1,02 shows it it under DSL overview that he finds something on the receiving station and then equivalent again again-synchronized.
It that be can that he is defective?

In any case one thank you for the MOD!!!!

MfG
WebZ@k
Quotation:
Quotation of WebZak Contribution indicate the image for the G3220 on my nigelnagelneuen has routs tried out. That rout bootet.
That is already times very good.

Quotation:
It does not synchronize simply at my connection.
If I down degrees to the 1,02 shows it it under DSL overview that he finds something on the receiving station and then equivalent again again-synchronized.
It that be can that he is defective?
Have do you nen work RESETs made? If one changes between version 1.X and 3.X, one must that, says at least official release Notes.

Within the range DSL etc. I no changes made. Which concerns the image, was the exciting question actually only whether it bootet.

(I am by the way off heut evening in the vacation; it can be that I then longer did not poste.)
Thus rout bootet.
Factory setting loaded. -> None synch. Fritz box hair dryer Wlan has a Synch. I will try it out today again at another DSL connection. I have so the assumption that either rout is, or my offerer (HTP) is nevertheless not completely compatible.
MfG
WebZ@k
Rout bootet and everything runs
have the 3220

now things would be as lufs or Netfs or Nas very interesting, as get I it naturally in such a way a Ext3 Hdd on usb to mounten

MfG
Happy
@xor16rox

The left for SMT-G3210_V3.01_130808mod.tar is not yet up http://bitflip.de/samsung/ linked

Super work!!
@happyerazor:

You would have to find the Linux Kernel 2.4.20-AMAZON you and take the normal 2.4.20er and to CROSS-compile and into the firmware image push then the SOURCEs for ext2/ext3 (I assume times). Since I strive myself already times with the Toolchain made, I try times whether which can be made.
if I to ask times in such a way may do have myself someone made mod for the 3010 to write???

HP: didn't it also gladly to make if I would know install with which linux system it works has times Ubuntu comes thereby so well clearly which uses it for it and there are not packs where all tool which I needs thereby is direct?? )
@nbx2001

That would be super, I should then at least manually over telnet the Hdd as ext3 mounten to be able.
Are to test gladly always ready. If however someone into this whole Crosscompilierer rei a little to train would be it also super could do me. Experiences with Linux and Kernel compile have I so a little, but stop only on x86.

MfG
Happy

HP the whole pour for the Kernel give it with Samsung to the down load
I do not have times wget CROSS compiled (a guerilla war) one must ptimer.c patchen and ambesten all defines to remove and only still GET DATE time permit, anyhow was it the only possibility, as I to compile to move could, the pos ix-timers liked he somehow also. Habs tested, runs also completely well, despite any error message of routs.
I sit at present to ctorrent to compile, despair however somewhat from open SSL, uclibc and their large file attitude.

HP: Thus open SSL not with the message “uClibc which built without large file support!” , must one breaks off in crypto/bio/bss_file.c the following paragraph delete

Quotation:
#if defined (__linux) || defined (__sun) || defined (__hpux)
/* Following definition of aliases fopen tons of fopen64 on above mentioned
* platforms. This of makes it possible tons of open and sequentially ACCESS
* files more larger than 2GB from 32-bit application. It of does emergency allow tons
* cross beam them beyond 2GB with fseek/ftell, but on the OTHER hand *no*
* 32-bit platform permits that, emergency with fseek/ftell. Emergency ton mention
* that breaking 2GB limit for seeking would require surgery tons *our*
* API. But sequential ACCESS suffixes for practical cases when you
* CAN run into large files, look for as fingerprinting, thus incoming goods CAN let API
* alone. For reference, the cunning OF 32-bit platforms which allow for
* sequential ACCESS OF large files without specially “magic” comprise *BSD,
* Darwin, IRIX…
*/
#ifndef _FILE_OFFSET_BITS
#define _FILE_OFFSET_BITS 64
#endif
#endif

Tadadadaaa

ctorrent-dnh3.3.2

Bt_content.cpp, if one does not want to compile it with openssl-sha1, simply those must be gepatcht defines for it into shape connecting piece and then runs the compiler. Program runs problem-free, torrent files before with wget downloads.

Much fun thereby
So, I have times the Kernel through-compiled with ext2, ext3 and ntfs with write support. I have however no notion, where one puts those down correctly, to hang up I have it tried from the USB stick by means of modprobe but vll. me if someone can do one taps gives, has no external ext2/ext3 turns out
Quotation:
Quotation of xor16rox Contribution indicate The problem with the G3220 is stop that I cannot test for lack of hardware. Therefore it would be good, if as with the G3010 someone were, which possesses actually sone crate. With the instructions, which gepostet syncBit, that is really not more difficult…

Because I was degree thereby, I now however times rehearse for the sake of an image for the G3220 made. That means however by no means that I will make for it further updates. On the contrary, I have for it actually no time and desire. Thus Freiwillige forwards.

Warning: the thing is absolutely untested. The probability that which goes inclined do not consider I very largely, but at least theoretically knows ne box scrap irons. Use RK your own risk.

http://bitflip.de/samsung/SMT-G3220_V3.00_140808mod.tar

And if someone dares, which to bottles, please as soon as possible it acknowledges whether the box still lives. In emergency one could probably at the serial console still which save, see. here and here.
Straight one tested and works so far well. In any case one top…
Hello,

I am to despair….

I now am since approx. 3 months on look for the Feherlsung.

I have the 3210 and a Web server also of the super with mine
Fritz box SL Wlan did not run however with Samsung.

Every time I from the network on my Domain zureife land I on rout go from the outside everything one-way-free!

I believe which I the haven for the Web interface to change must which I then not with:

www.???? .de (no advertisement!)
separate with:
www.???? .de: 2001 (or every other haven not 80)

But the glabe I must know is something else
Thus with other suggestions ask….

Naja thanks

Greeting

MarGre
In order to come again on the ext2/3 problem back:

I do not believe, which folds it so simply with the Kernel modules, since the Toolchain with Large file support, just as also the Kernel would have to be compiled. The Kernel on the SMT-G devices activated, could however no Large file support thus Tricky become.
Hello,

@nbx2001:

the Large file support is however only for files > 2GB importantly, for files under this border should function it however.

I have times tries your ext2/ext3 modules to merge. That did not function unfortunately:
1. still the JBD Kernelmodul is necessary and for ext3
2. I received each quantity of error messages of the type “Relocation OVERFLOW OF type 4…”
That I however solved, by I the modules with the option - mlong calls compiled.

Thus then also shop of the modules folds:
Code:
# insmod /ramdisk/ext2.o 
Using /ramdisk/ext2.o
 # insmod /ramdisk/jbd.o 
Using /ramdisk/jbd.o
 # insmod /ramdisk/ext3.o 
Using /ramdisk/ext3.o
So far so well. Unfortunately I it nevertheless did not create, one with ext3 formatted USB stick to mounten:
Code:
# mount - t ext3 /dev/sda1 /mnt/usb-storage/
 mount: Mounting /dev/sda1 on /mnt/usb-storage failed: Invalid argument
dmesg says:
Code:
hub.c: new USB DEVICE 00:0 d.2-1, assigned ADDRESS 17 [SPEED 3] [STROKE SPEED 3]
 usb.c 2318 USB_SPEED_HIGH speed=3
 more ================newer storage================
 *** storage_probe: Bulk, transparency SCSI, JetFlash, measure of STORAGE DEVICE, VKAN0GQM 
WARNING: USB measure of STORAGE DATA integrity emergency assured
 USB measure of STORAGE DEVICE found RK 17
 SCSI DEVICEs sda: 7987200 512-byte hdwr second gate (4089 MT)
 sda: Write protect is off
 sda1
 VFS: To Can't find ext3 file system on dev sd (8,1).
The mounten on another computer folds however problem-free.

I my compiled modules attached. Perhaps one of you would like to test that times.

Greetings
dirtybit


EDIT:
I the whole also times with ext2 tested, unfortunately same problem:
Code:
# mount - t ext2 /dev/sda1 /mnt/usb-storage/
 mount: Mounting /dev/sda1 on /mnt/usb-storage failed: Invalid argument
dmesg:
Code:
VFS: To Can't find ext2 file system on dev sd (8,1).
In addition I have forgotten to mark that one must pay attention with ext3 to it, to limit the Inode size to 128 byte those am with newer systems default to 256 set.
Code:
mke2fs - j - I 128 /dev/..

Hello, I is again here and has some problems. I procured myself the SMT-G3210, because I have aborts with Netcologne and the Fritz box in 50189 Elsdorf very often. Those are allegedly (as per. ) Because of the chip set are to forums and with the G3210 any longer do not emerge. Therefore I have mod the verse over this forum. 3.0 downloaded and installs, afterwards power always flashed and did not stop not. This problem left itself with mod verse. 3.01 loosens, power burns and only the DSL LED flashes. When I had then entered the own Provider data into the basis configuration, the error message came to the test (still flashing DSL LED): „PPPoE determination missed. Exceeding the time, no feedback of the server “. Both the DSL connection of the fragment and without fragments tried. What now do I make, so that rout runs?
HP: in other place of this forum I found a contribution that mod the version is no longer necessary, because with Samsung to down-load-end likewise the all Provider supports now. Should that is correct and I try?

Thank you,
Hans
Quotation:
Quotation of hahaha9 Contribution indicate HP: in other place of this forum I found a contribution that mod the version is no longer necessary, because with Samsung to down-load-end likewise the all Provider supports now. Should that is correct and I try?
It is correct that newer versions of the official firmware support other Provider. The Mod makes also no interferences within the range DSL/Voip; therefore it is improbable that your problem which thereby to do has.

The Mod effectuation only a few minimum changes, in order to give to the user better control over the system, so that it can make large changes easily. Therefore I reject also most “feature Requests”, because I want to keep the Mod simple and minimalistic.
@DIRTYBIT
Super thanks.
I thought already I employ myself times again bld.

how highly are the data rates actually with a ftp transfer with you? Lean 1,3MBs is despite alleged usb2.0 with me

MfG
Happy
Still a few small nose fixed updates for the Mods. The 3210-Version successfully runs since today with me. For the 3010 - and 3220-Versionen still applies that they are untested and potentially dangerous. There I ask a positive success message of a courageous tester, before I her left.

http://bitflip.de/samsung/SMT-G3210_V3.01_080908mod.tar
http://bitflip.de/samsung/SMT-G3220_V3.00_100908mod.tar
http://bitflip.de/samsung/SMT-G3010_V3.01_110908mod.tar

Changes Mod2
Quotation:
Quotation of happyerazor Contribution indicate @DIRTYBIT
Super thanks.
I thought already I employ myself times again bld.
Gladly, but ' s still does not go.

Did you test my Kernelmodule times?
Which concerns the Kernel, which is good message:

# uname - A
Linux localhost.localdomain 2.4.20-AMAZON-3.1.5-M1664-V31-xor #2 does 9 00:07 to September: 07 CEST 2008 mips unknown

Compiled bootet with me now through and, if I replace the missing include/asm/amazon/model.h by from the Gigaset Kernel. The bad message is that I described the same problem above with ext2/ext3 as.
Quotation:
Quotation of xor16rox Contribution indicate # uname - A
Linux localhost.localdomain 2.4.20-AMAZON-3.1.5-M1664-V31-xor #2 does 9 00:07 to September: 07 CEST 2008 mips unknown
Cool one!
The Kernel to boats I then any longer did not dare.

Unfortunate that he does not recognize nevertheless the ext3, I had the USB stick in the suspicion with me already…
Property straight times the Mod software on my 3010 drauf made and run so far without problems
Hello,
the solution found: NetColgne needs somewhat unusual connecting parameters with the VPI/VCI - values.
(and before-one-places in the G3210) are usual: VPI == 1, VCI == 32
NetColgne uses however: VPI == 8, VCI == 35
afterwards it functioned. I will report whether now the aborts usual with the Fritz box do not emerge any longer.

Property however still another supplementing question: In the Fritz box I could not use Traffic Shaping for speed improvement, with the G3210 find I anything in addition. Can someone help me?
Quotation:
Quotation of xor16rox Contribution indicate Still a few small nose fixed updates for the Mods. The 3210-Version successfully runs since today with me. For the 3010 - and 3220-Versionen still applies that they are untested and potentially dangerous. There I ask a positive success message of a courageous tester, before I her left.

...
http://bitflip.de/samsung/SMT-G3220_V3.00_100908mod.tar
...

Changes Mod2
, Functions to thanks at first sight as before, thus good.
Property times ne question: One can be used the current firmware in such a way fashions that samsung the box 3210 as Repeater behind Fritz a box 7170 can.

MFG

Mirko
Rear one,
it only unfortunately goes also without mod without VIOP function developing there the box an Internet entrance over the internal modem or LAN1 vorausetzt around a VOIP connection. The normal LAN and Internet access over WLAN fold however perfectly.
It would ingeniously be if one a solution find there could.

Greeting

Juergen
I would like to use it at present only to the WLAN enlargement without voip.

And does not go with the current because I mean 7170 as master further to use would like. Alone through OFF and fax function of the 7170.

greeting mirko
Hello Mirko,
you can use your Fritz also further problem-free as masters.

Samsung on Repeater, DHCP out, assigned (within the same range as Fritz box), WLAN same channel as Fritz register celebrations LAN IP to MAC von Samsung in Fritz.
Habs all thing only with incoming inspection key tested and goes perfectly.

Greeting

Juergen
Quotation:
Quotation of xor16rox Contribution indicate Compiled bootet with me now through and
As it looks then with the modules such as WLAN and CO out. After somewhat participates also non GPL software/driver investigates. Can you address the internal Atheros with the pure Kernel? It would be interesting whether one the equipment with a newer Kernel and/or. OpenWRT/Kamikaze to equip could.
Firmware for the 3220 installs.
Runs marvelously.

@dirty your Kernelmodule becomes I at the incoming goods times on routs itself packs.

Thanks

MfG
Happy
Great success! After emsiger search for (quite stupid) an error (here thanks at Haucke) open WRT runs. So far I tested only the default configuration, a larger image bake degrees industriously before itself.

Edit: Wlan does not run (no PCI driver), modem runs not (no drivers)
Hello tarzan,
very interesting.

Are open WRT beginner.

you can have to be loaded to few words briefly to explain which files as on the box. (and where they to find are)

Thanks
Rear one,

you must open WRT von Scratch build, therefore you need first times a Linux Maschine/VM. Then checkst you the open WRT drunkenness by SVN/GIT out. Then you bake yourself an image after the guidance in the Wiki. That pastry-ends firmware image pushes you then by TFTP on routs (on the 1.XXer firmware down degrees thereby you into the Bootloader console comes before - but you must rout screw on and the serial console (described as in the Wiki) to tap. Attention, runs with 3,3V, not with 5V! An old Nokia data cable its services, the pin allocation you must stop fast times with the circuit analyzer by Durchklingeln in the best way rausfinden fulfilled here).

The Kernel arrived meanwhile with 2.6.30, however ' s still gives no support for Voip, to DSL the modem or the PCI bus (and thus the Wlan map).
Hello,

does it give after an open WRT installation also back to the freenet firmware?

Which is then with rout to do.

Thanks
Yes, you can up-play the freenet firmware over the submarine console again. Firmware tar from freenet and on nen TFTP server must unpack put. Subsequently, you know submarine Environments with in the environment variables of the deposited Skripen (upgrade_kernel, upgrade_rootfs… ) the individual parts freenet image again bring in.
Hello,
I would like to be able to use the serial interface /dev/ttyS0 for other tasks freely.
At present it is probably used by the submarine or the Kernel for the expenditure.

Is there a possibility to switch off?

If:
Where there is the Sourcen for the submarine image of the SMT and/or. the open WRT?


Thanks for answers
Look times here past:

http://wiki.gpl-devices.org/wiki/Samsung_SMT-G3210

However I recommend to leave the serial interface usable further at least over submarine, otherwise you cannot rout in case of a Softbricks no more recovern.
As that that is temporal expiration with the boat.

Only that comes submarine and starts later the Kernel.

The serial expenditure is steered only by the submarine or takes over if the Kernel runs later these control?
I am not an expert, but idR. the Bootloader starts the Kernel, which holds then control of the system. Therefore I would say the use of the serial interface am independent.
I should have to switch the serial one off with the submarine, because not differently possible. I can accomplish then not also over Jtag a Recover.

System knows telnet and update Flash fkt contains and is thus over net attainable. (An SW-boat-error or Config error would have to then already be in the entrance, which does not start or closes the system any longer)
Quotation:
Quotation of more ipsurfer Contribution indicate Edit Novize: In accordance with filling ratio that Forum rules deleted
That exceeds now means horizon, and JTAG I so far still nich rank-dared itself. But actually it should go. No guarantee.
Hello first times,
only times to get straight, in the Routermodding are I a total DAU, I have of course as an overview of such things as e.g. Open WRT or which a serial console is, but otherwise I cannot begin other things anything

I am, that again here am my first contribution.

There thus, I have a g3210 which I in next time as WDS WiFi Bridge SMB server maschiene to abuse (for my XBOX Classic) I already already informed, white I that the WLAN map yet not functioned.
Therefore I wanted to ask, as look it, and/or. How long it needs to such a driver is developed, and/or postage ore is.
Because I mean to have seen a driver for this map.

Further glad gefrickel
The problem is the Wlan driver separates less the PCI driver… The map actually should run with Madwifi problem-free. Unfortunately the driver delivered with Samsung firmware does not function like it seems in to station the mode.

Edit: If you the equipment eh as WDS Repeater to use want should that however nevertheless no problem be… Xbox by cables to, a Samba server runs nevertheless already on the original freenet firmware or?
Hello tarzan,

now the open WRT image installed.

Unfortunately I do not come into the Web surface.

That remains apparent hanging boat.

In the console I see the following information:


Code:
AMAZON # �Head: Amazon version 1.0.0
 DRAM:  64 MT

 Head: reloca_code start
 Head: relocate code finish.
   Image name:   submarine image
   Image type:   MIPSirmware (lzma comressed)

   DATA Size:   38673 bytes = 37,8 KB
   Load ADDRESS: 80100000
   POINT:  80100000
 Disabling all the interrupts
   Uncompressing UBoot image….   Uncompressionmpleted successfully with destLen 117160.
  Head: Jumping ton submarine into the RA " �!! �


----------------------------------------------------------
    SAMSUNG IAD platform
    Submarine 2.6.0-M1664 Flash: N (April 23 2007 - 12:24: 23)
----------------------------------------------------------

In env_init: env_ptr = 0xb3ff7000
 For enviornment CRC32 is OK
 board: AMAZON Yangte version, chip CCU speed 235 MHz
 DRAM:  64 MT

 relocate_code start
 relocate code finish… 

Duck ring flash_init ()
 flash_get_size
 type is 00000001/0x00000001
 type is 0000007e/0x0000227e
 Flash: 16 MT
 env_relocate [224] malloced ENV RK 83abf408

 Initialize DEVICE…
In:    serial
 Out:   serial
 Err:   serial
 Net:   AMAZON SWITCH IAD
 warning: AMAZON SWITCH IAD MAC of adresses don't match:
ADDRESS in SROM is         44:00: 00: 00: 00: 00
 Addres in environment is 00:16: 32: 8A: 1D: 38


 type “run flash_nfs” tons mount root file system of over NFS

 ### main_loop duck-talk: booelay=0

 ### main_loop: bootcmd= " run flash_flash "
 press enter key ton stop autoboot:  0 
+do_bootm, argc = 2,  
nTmp=0, v=bootm 
nTmp=1 argv=0xb3060000 
## Booting image RK b3060000…
Bath Magic NUMBER
 AMAZON #
Kanst you help?

tschss


edit:
It is very in former times version conditions of open WRT. Possibly without Web interfaces, but as I get raus whether open WRT run?
With which address would the HW have to be pingbar? Which Kommands is as callable?

Assistance for an open WRT beginner
Hello,

sorry for OT, but a question has to rc.local:

If the OpenVpn has, someone nice-proves a few sides compiled to to run before brought, works under the 3,02 Mod also very well. Only problem:

I start OpenVpn and a doing by Rc.local.
If I rc.local implement function everything manually perfectly and he start do and openvpn.
However it does not start rc.local with the system start. Does someone know the problem?

here times contents of mine rc.local:

Code:
#! /bin/sh

 CD /ramdisk/mnt/usb-storage/2GB-STICK_USB-Flash-0/openvpn
 insmod ./tun.o
 ./openvpn --mktun --dev tap0 &
 ./openvpn --config xxx.conf &
thanks already times

greet
Quotation:
Quotation of davegriebel Contribution indicate I start OpenVpn and a doing by Rc.local.
If I rc.local implement function everything manually perfectly and he start do and openvpn.
However it does not start rc.local with the system start. Does someone know the problem?
You should guarantee Erstmal whether rc.local it is not actually implemented or whether the instruction does not function when starting.
http://bitflip.de/samsung/rclocal-howto.html
(In your contribution you have e.g. the file names once wrongly written. So that could already times not function.)

I could also imagine that possibly. the USB stick is not yet fully initialized, if the Startup Script is implemented. Versuch's times with one “sleep 30” or so at the beginning of the Scripts.
For the moment I would not recommend open WRT to a beginner on the smt-g3xxx to bottles.
It is many simpler via tftp a RAM image to boats.

Conditions are:
Tftp server (e.g. Pumpkin for Windows, tftpd hpa under ubuntu)
Target image --> RAM disk (lzma) selected (under open WRT: make menuconfig)
Firmware 1,02 on rout

Kurzanleitung for it for submarine:
- press with boats by “more enter” in submarine change
- setenv serverip (IP address of tftp the server)
- setenv boat file openwrt amazon uImage
- optionally: setenv ipaddr 192.168.1.2 (IP ADDR-eat rout change)
- optionally: setenv bootcmd net_nfs (then the RAM image tries to load from tftp the server to & start with each boat)
- optionally: saveenv store (Environmentvariablen durably in the Flash)
- run net_nfs (load the RAM image from tftp the server and start)
- optionally: RESET (Reboot of the Routers)

If want to try their open WRT out only times briefly, omit you simply with optional marked instructions.


@tarzan:
Could you that again up-play the freenet/Samsung firmware in more detail describe?
, user loves! I pursue your Thread for a long time as a guest, but after months-long Mitlesen I struggle through myself now now nevertheless once to write something.

I tried, here the programs mksquashfs lzma and unsquashfs lzma and here to download mkimgae as source code. So far, so well. I got also problem-free the Magic Numbers gepacht. Now I wanted to compile the programs on my system (Ubuntu 9,10), but failed. What? Now, probably on extremely modest C (and at all programming) means knowledge. I do not know simply exactly, which instructions I must enter, so that that through-compiles cleanly. (Everything which I so far translated, could do I with GCC - o foo.exe bar.c translate) at least with mkimage I could produce an executable file with the following instructions (whether it functions, am another thing): Code:
1. CD… /u-boat 1.0.0/lib_generic
 2. GCC crc32.c - I. /include - C
 3. CD… /u-boat 1.0.0/tools
 4. GCC mkimage.c ../lib_generic/crc32.o - I. /include - o mkimage
Therefore my question: Me someone knows assistance with compiles to give or has somebody the finished compiled (and with Magic NR. ) did Binarys gepachten, executably on nem Ubuntu 9,10 rumliegen at home and could them somewhere to me send or high-load?
I would like to adapt actually only SMT-G3210_V3.02_010509mod.tar a little to my needs (the password to change [so that I do not have to again adjust it after each work RESET] and some cosmetic things in the Web surface). To the Krosskompilieren I would near-dare myself perhaps then later, but for the moment [me at least] also really programs on the box “are not missing”.

You like to forgive me that I come closer directly with a request at you and I understand thoughts as “come now again such a DAU and wants which from us” however I hope for your indulgence to return are I nevertheless always ready, the Community somewhat thus it in my forces stands… here also a cordial “thank-beautifully” for your employment to estimate I white that much. And believes me, I would not like mono logs to behave, not times relative!
Quotation:
Quotation of neldar Contribution indicate Could you that again up-play the freenet/Samsung firmware in more detail describe?
http://bitflip.de/samsung/troubleshooting.html
The last point should function from the submarine console.
Posting 2 after 6 minutes - there is also the changing function!
Quotation:
Quotation of yomi Contribution indicate Therefore my question: Me someone knows assistance with compiles to give or has somebody the finished compiled (and with Magic NR. ) did Binarys gepachten, executably on nem Ubuntu 9,10 rumliegen at home and could them somewhere to me send or high-load?
With me without setting with simple “make” goes…

I hang times my Binaries to, no notion whether those run with you.
Hello,
Without me to inquire before I have a G3210 freenet edition with Ebay for a few euro climbing ore, my question now (before the heap of technique scrap iron is with me):
- Can be I it without the berguru of the Firmwarepatchens, for other offerers (DSL over kielnet and voip over personal voip.de use ´? or should I buy equal part weiterverhkern and for a few euro more Fritz hair dryer Wlan?
Thanks for your Tipps
Greeting Ralf
Rear xor16rox,
I dare to state, which you use somewhere another Kompilereinstellung than I.
A reference to it gives already the storage location in the Kernel:
Sound core with me 4352 with you 4592
Sound with me 71884 with you 72652
I have the production in the Samsung Sourcecodepaket over make menuconfig then meke dep and then make modules.
I do not believe there can one wrong make HOWEVER I the Toolchain of you at that time with the option one much MMU existed compiled. I meant, which the AMAZON a MMU possesses. [Property again checked, the AMAZONE has definitief MMU and DMA (direct memory access)]
You can still remember yourself whether you had also so.
Because mine audio.o required for a DMA (direct memory access) manager, that is as far as I know part a MMU.
With the MMU no change resulted in.

I looked at myself times the Makefile in the sound file. There stands:
Quotation:
sound objs : = \
dev_table.o soundcard.o sound_syms.o \
audio.o audio_syms.o dmabuf.o \
midi_syms.o midi_synth.o midibuf.o \
sequencer.o sequencer_syms.o sound_timer.o sys_timer.o
...
sound.o: $ (sound objs)
$ (LD) - r - o $@ $ (sound objs)
thus the functions were also compiled purely audio.o in sound.o. Was noticeable to me also, which are make install_modules after only sound.o and soundcore.o in the Installziel.
It does not stand well!
After endless rumgefummel at the compiler options it went through then finally. But it kompliert me around strains the own sound core and snd usb drv not also.
With the sound core from the Samsung package it misses either:
Quotation:
unresolved symbol snd_compat_strlcpy
or with other attitudes
Quotation:
unresolved symbol strlcpy
I will still supply a few details.

Which I made in such a way:
Quotation:
Used versions:
alsa-driver-1.0.17.dfsg and
alsa driver 1.0.22.1 +dfsg
in the Datai:
/home/prediger/Source/GPL_3210/kernel/opensource/linux_2_4_20/include/linux/workqueue.h
/*Auskommentieren with ALSA kompiling*/
#define work_struct tq_struct
#define schedule_work (x) schedule_task (x)
#define flush_scheduled_work flush_scheduled_tasks
#define INIT_WORK (x, y, z) INIT_TQUEUE (x, y, z)
/*Kommentar Ende*/
work_struct the ALSA package defines the label

To which I continued to come with ALSA not have I once again the Unterverzeichnise of the Samsung SOURCE regarded. There it noticed to me that it gives under drivers/usb one audio.c. There times clean-looked and see, that is audio.c for the USB support. Property me then the Config.in outstandingly and see there, the make menuconfig brings the USB audio only, if PCI aktiev is.
Now the question at you, who finds the point in that menuconfig to activates the PCI. I did not find it!
Thereupon I set in my .config all entries with PCI, stored last, on y and see there with for nights the start of make menuconfig could I a “dream list” from USB devices within the range USB open, so also USB audio. And see there soundcore.o and audio.o loaded from the USB file on the box the business and with insmod. Audio USB stick purely and dmesg bring:

Quotation:
start down load of pages

pages downloadedport 2, haven status 501, CHANGE 1

***************** Default Deley after ***********************
haven 2, haven status 101, CHANGE 1

***************** Default Deley after ***********************
pdev -> devpath [0] == 0
hub.c: new USB DEVICE 00:0 d.0-2, assigned ADDRESS 2 [SPEED 2] [STROKE SPEED 0]
usb.c 2323 USB_SPEED_FULL speed=2
usbaudio: DEVICE 2 audio control interface 0 has 1 input and 1 output AudioStreaming interface
usbaudio: DEVICE 2 interfaces 2 altsetting 1 channels 1 framesize 2 configured
usbaudio: valid input SAM-polarizes guesses 24000
usbaudio: DEVICE 2 interfaces 2 altsetting 1: format 0x00000010 sratelo 24000 sratehi 24000 of attribute 0x00
usbaudio: DEVICE 2 interfaces 1 altsetting 0 does emergency have at final POINT
usbaudio: DEVICE 2 interfaces 1 altsetting 1 channels 2 framesize 2 configured
usbaudio: valid output SAM-polarizes guesses 48000
usbaudio: DEVICE 2 interfaces 1 altsetting 1: format 0x01000010 sratelo 48000 sratehi 48000 of attribute 0x00
usbaudio: registered dsp 14,3
usbaudio: constructing mixers for terminal 3 type 0x0301
usbaudio: registered mixers 14,0
usbaudio: constructing mixers for terminal 6 type 0x0101
usbaudio: registered mixer 14,16
usb_audio_parsecontrol: usb_audio_state RK 81e88260
tata. Now I still the dev on the left of baune must. Need a OSS mixer and a OSS Commandline Audioplayer.
Juhu of the Dudelt!!!!!

Still another problem with sound USB stick had the TP6911 my.

One needs:

zlib_1.2.3.3.dfsg.orig.tar
libmad-0.15.1b.tar
libid3tag-0.15.1b.tar
madplay-0.15.2b.tar
and I still because of the TP6911
sox_14.0.1.orig.tar

after setting:

export CC=/home/prediger/Toolchain//toolchain_mips/bin/mips-linux-gcc
export LDFLAGS= " - L/home/prediger/Toolchain/toolchain_mips/lib - L/home/prediger/Toolchain/zlib 1.2.3.3 .dfsg - L/home/prediger/Toolchain/libmad-0.15.1b - L/home/prediger/Toolchain/libid3tag-0.15.1b - statics "
export CPPFLAGS= " - I/home/prediger/Toolchain/toolchain_mips/include - I/home/prediger/Toolchain/zlib 1.2.3.3 .dfsg - I/home/prediger/Toolchain/libmad-0.15.1b - I/home/prediger/Toolchain/libid3tag-0.15.1b - statics "

and jewieils ./configure - host=mips-linux
and make
read yourself all behaviourless through-compiled.

The dear path kan one also

export LD_LIBRARY_PATH=/lib: /ramdisk/SMT_ext/bin
extend on the box.
Quotation:
Quotation of Beethoven Contribution indicate Rear one,
it only unfortunately goes also without mod without VIOP function developing there the box an Internet entrance over the internal modem or LAN1 vorausetzt around a VOIP connection. The normal LAN and Internet access over WLAN fold however perfectly.
It would ingeniously be if one a solution find there could.

Greeting

Juergen
Hello Jrgen,
you have meanwhile a solution for o.a. Quotation found?
I look for for a possibility via WLAN Voip to run to get.

With Siemens a SX 541 I have it get. These do not rout is however as comfortable as Samsung.

Greeting
Quotation:
Quotation of kaimaik Contribution indicate Hello Jrgen,
you have meanwhile a solution for o.a. Quotation found?
I look for for a possibility via WLAN Voip to run to get.
Greeting
The problem is, which the G3210 always sees itself as gateway. e.g. config also the time over time servers might not be able to be updated any longer in servants. Porbiers times out in which you in correspond the menu times store click. The time of smells do not update themselves.

Around in addition-gotten you must nevertheless fashions.

after that the box started must you it the following coma DOS under rejoicing.

killall dnrd ; killt the own DNS service of the box
/sbin/route ADD default gw 192.168.178.1 ; your Fritz box sets as gateway
echo “name server 192.168.178.1” > /ramdisk/etc/resolv.conf
Hello Jrgen,
has obeyed like you it in such a way wrote.
With the time server is correct.
It functions now.

Only with the Voip does not go yet.
Is there there still which “makes”?

Greeting
Quotation:
Quotation of kaimaik Contribution indicate Hello Jrgen,
Only with the Voip does not go yet.
Is there there still which “makes”?

Greeting
With the Voip there is still the thing with the STUN service. The boxes are konzepiert usually so the fact that they do not use the STUN, since them as if rout directly the public IP use can, and thus the STUN does not need service. The STUN keeps artificially the temporary haven allocation in the Masquader of the Eingangsrouters upright, so that the Voip equipment remains from the outside attainable. That is however unfortunately not my field of activity. I say times - which asks next ones.
I hung now over the serielen haven of the box a 2x16 indication display and an IR remote maintenance with Philips RC5-Codierung to. Since I used for it a Microkontroller anyway, I wrote the software in such a way the fact that the Microkontroller announces itself simply on the console as root and indicates the expenditures for CONSOLE on the display and the IR-Cods solves appropriate echo coma DOS from then the Datai into the RAM disk with the transferred RC5 code writes. I hang times the code for the Controler to. However badly documented.

Since I did not shift the USB stick inward hand the cooling of the box any longer and I had to help in little.
, Not badly the idea =) I will also times make rear Prediger, as soon as I the telnet to run has ^^ which not really wants. What for a remote maintenance did you use?

Greeting Florian
Quotation:
Quotation of Prediger Contribution indicate Juhu of the Dudelt!!!!!
One needs:

zlib_1.2.3.3.dfsg.orig.tar
libmad-0.15.1b.tar
libid3tag-0.15.1b.tar
madplay-0.15.2b.tar
and I still because of the TP6911
sox_14.0.1.orig.tar
I have determined that madplay still of the a few desires leave open, if he is to run in the background. The multiply decimal would not be ideal gets I however around strains crosscompiled. I white however, whom it some has business, only do not find I anywhere a guidance, how. Already times someone is gestolpert over one of you. Necessarily one does not have to be then probably still adapted for MIPS, gets.
Hello,

mad achievement. A little gegoogelt.

Here two places of discovery:

http://diy.sefikuv.net/asus-500g-del...ng-tenx-tp6911
- a similar project

and
https://wiki.graz.funkfeuer.at/BackyardRadio
- Open WRT with multiply decimal
- Source of mpd_0.12.0-1_mipsel.ipk

I hope it help!
Unfortunately on the left of do not help me.
They do not point only like one the multiply decimal use however it contain guidance to crosscompiling.
With windows is it like that. You load yourself a program, install it and it run. But Windows runs only on x86-Maschinen.
With Linux is that different. Linux one knows nearly on each architecture to runs to get. One zaht however with the price, if one is an architecture used those in little exotic to have to compile all Progamme suitably architecture. That can be done also, because nearly all programs are published in their C-source code. It becomes correctly merry if one e.g. a program on a x86 for e.g. an MIPS architecture like the G3210 to compile wants. There one must make some attitudes thereby the program on MIPS and not on x86 is compiled. Some programs let that make good with itself. With others one stochert completely beautifully in the gloomy soup, particularly if programs are dependent still on other programs.
Quotation:
Quotation of Prediger Contribution indicate The multiply decimal would not be ideal gets I however around strains crosscompiled.
Perhaps helps (for me always good point of approach ) Open WRT multiply decimal, particularly concerning the “configure” - parameters, dependence and Patches.

“If need be” it goes mostly in such a way: Open WRT drunkenness install, “amazon” equipment select and the multiply decimal package, after which (are enough (!)) fault up then if necessary in the Makefile with the LDFLAGS still” - statics " add…

Jrg
Nabend, the instruction unsquashfs lzma is not found with me, although I implemented the make instruction. I get the error message that he does not find the instruction. Can someone help me there further?

Greeting Florian
In which listing are you? Possibly you must enter the path there completely, in the kind path/to/to file/unsquashfs lzma. If it lies locally in the listing, in which you are ./unsquashfs-lzma.


Jrg
That was my error I has that. /forgotten had, thanks ^^

now the following, I comes becomes equivalent times schaun whether here already forwards came,

Cant find to A SQUASHFS superblock on ./temp-work/stript-rootfs.img

settled oneself! =)
And before the Uboot part “cut off” (point 2 in the first contribution of the Threads)??

Jrg
That I did not have already however as I with superblog had changed, had I make implemented with unquashfs lzma, but to it went then also.

Sooo now have I everything divided now goes to ' s to the preserved.

One can do with routs Lan 1 to WAN in such a way to adjust which one with pppoe data in-select can I was already to stbern has however not yet so correctly which found.

Greeting Florian
article.voiper.org
   Copyright@2010   Sitemap