[solved] FRITZ! Box hair dryer WLAN 7240 CO2 Telefonie of aborts…. - VoIP General, VoIP News, VoIP Providers, VoIP hardware, VoIP software, VoIP Technology

Hello dear forum,

I have an O Premium surf rout, which I would like to send now against a Fritz box in pension. Now has I problem, which everything so far function ore, up to which Telefonieren.Wenn borders I the magic 2 minutes reaches, resettet the box simply.

I tried it with 2 boxes: 7170 and 7240, both the same problem…

PLS HELP: -/

Greeting
Sven

which firmware do both boxes have?
when did you make last times a Recover?

how are the DSL connecting data?

Quotation:

Quotation of informerex

which firmware do both boxes have?
when did you make last times a Recover?
how are the DSL connecting data?

Q: which firmware do both boxes have?
FRITZ! Box hair dryer WLAN 7240 (UI) Firmware design 73.04.80-15941
FRITZ! Box hair dryer WLAN 7170 (UI) Firmware design 29.04.80

Q: when did you make last times a Recover?
the boxes once set on factory settings, more recover evenly straight has both…

Q: how are the DSL connecting data?
http://www.appscene.de/viewer.php?id=545451dsl.jpg

The Login data looks in such a way:
http://www.appscene.de/viewer.php?id=689024dsl2.jpg

I hope, which you mean this data

Greeting

if I remember correctly, is in debrand necessarily, so that the CO2 attitudes become “visible”. (and/or. 2.PVC to be furnished can)
//EDIT: use this Tool

Thus again “from the front”

HP: Full quotations on a Posting refer before, are not not gladly seen
You can change appendices over > extended > Appendices high-load. do not use (external offerers)

so, the box now is entbranded, and nu?

now a work RESET and a PoR (= 5 min. ALL cables remove).
Then the box for a new Konfig would have. prepared.

under sip CO2 would have to appear ua.

Hello,

1.) your question would be in CO2 forum range surely better waived,
2.) it is not said that the Providereintrag of CO2 is visible now,
3.) you should the box only times so, how here described, setting-up.

HP: If a Mod were so friendly please and would shift your Thread after CO2, Thy!

CO2 attitudes more largely 80 would have to run, as one div with the L.G. positive Postings to infer can.
It is meaningful to examine after the work RESET first times whether CO2 is present, thus saves one those indiv. Attitudes.

with xx.xx.76 geht's somehow “more approximately” with CO2

I unfortunately cannot however down degrees or?

so raus, and work RESETs made, I examine 5 min cable times….

But CO2 is not among sip the offerers… sees appendix

starting from xx.xx.80 CO2 appears only among DSL offerers

So now I have the problem, now which I made the error, whom I selected otwo, and get I the box not mhr highly. more recover says, which I have a wrong image

heelp

Quotation:

Quotation of Sziebeck

which I selected otwo

where?

you have further which version now drauf and which Recover version have you?

I made laboversion druff:
73_04_80-15941

however unfortunately find no to recover version for it

and this Recover?

sp the picture attached above…

thus I can do net recovern, because it is the wrong version, the 80 without -…

then times entbranden and is good

that is rehearses, tool says then IP wrongly. thus ' s will more recover go only with

I would make, then would try PoR again.
if it should not go, take og the Tool to recovern.

with tool he says to me, where the power pack rausziehen was, which does not tune the IP… I think, which is shot-up the box

but I have the 7170 now entbranded,
it makes only unfortunately always still the RESETs… must we far-that-makes there…

greeting

there are 2 Tools

A.) the normal more recover, you have that at the conclusion as screen SHOT
b.) ruKernelTool

take the Tool of b)
which occurs to me however straight, with that laboratory (must have been for mini) had AVM made from the version numbering.
it would have to be smaller recover 80, which fits for the laboratory.

thus the 72 it I can do probably forget it speak still not times more on recover tool on…

then rather with the 7170 continue please…

now remain nevertheless times with the 7240, that can nevertheless be that both Tools do not go.

thus: with the Recover tool he finds the box without mains cables,
but if I am to clean-put this, then he looks for himself dead, until tool after long time breaks off.

if I take the other one tool, he finds the box, up to the plug clean-puts, then says he, which is invalid the IP….

greeting

Network map IP Eintellungen should be automatically” adjusted to “, perhaps times examine…

okay, I try s again… pls WAIT: - 9

thus, even with rec tool (small alsxx.xx.80) and car the IP does not go it

rec tool always still incompatible fiirmware says

and debranden goes? Over telnet it must go nevertheless also
echo “firmware_version avm” > /proc/sys/urlader/environment

debranden went

now stop goes nothing more… how do I make with telnet?

Greeting

ask times skyteddy whether it here “past look” can, in order to render to you help.
the Tool of it is ingenious and so far nearly each box to the life aroused.

1.Telnet in Fritz! Box by telephone activate
2. cmd windows call
3. Telnet Fritz box
3. Web password enter if necessary
4. echo “firmware_version avm” > /proc/sys/urlader/environment
6. quit
finished

will I times try, telnet tomorrow by telephone, how the code was?

...

Well, all codes are in the FAQ, chapters 4 listed, only times clean-look

@Sziebeck
sorry, but it can be that you expect that one takes you at the hand and you want only a clicking RA line.
we write here the appropriate tips and supply appropriate left, which you only read and process must.

so, sorry for my errors…, habs now production. ...

the box lives again, has only on a test computer on the work XP had, there went it perfectly….

Thus, now again to the abort problem, I will at home attach the box, and then announce ch me to word….

play in each case those current final version + examine whether the box are actually entbrandet.

yes, I have now no 1&1 logo more, and have in Internet entrance data the rider also CO2 to now be located….

So, after long fiddle have I it get.
With the box inside the veins were free in the break protection of the power pack.

If the box read got, it fell.

I opened the power pack now, and the error repaired. Since then the box does not fall.

Greeting and many thank you to all involved,
Sven

ask in the 1. Posting go changing on > extended > register and in Headline [solved]
Thanks for feedback and now much fun with your box